What is a Blum hinge?

Blum hinges are the choice of many woodworkers the world over for their quality, craftsmanship, and lifetime guarantee. This post will explain how to choose the right Blum hinge to make your cabinets look their absolute best and allow them to function with ease.

Also to know is, what is a full overlay on a hinge?

Full overlay hinges are for individual cabinets or the cabinets on either end of a run of cabinets. (Source) Half overlay hinges are intended for pairs of doors in the middle of a run of cabinets, where two doors have their hinges mounted on opposite sides of a shared middle partition.

What is a full overlay door on a cabinet?

Standard overlay cabinets (also called traditional overlay) tend to be less expensive and do not require hardware because there is enough finger space on the side of the cabinet door or drawer face. They also have more exposed face frame, with at least 1 ¼ inches on all sides of the doors and drawers.

How do you measure double demountable hinges?

Apply a piece of tape to the frame of the cabinet on the hinged side of the door so that it even with the edge of the door. Open the cabinet door and measure from the edge of the tape (inside edge) to the edge of the opening of the cabinet. This is the overlay. A partial inset door is used on a face frame cabinet.

Where is BLUM hardware made?

Blum is an international manufacturer of furniture hardware. It is a family-owned company based in Höchst, a municipality in the Austrian province of Vorarlberg. Production facilities are mainly located in Austria, but the company also has production plants in the United States, in Poland and in Brazil.

What is the standard thickness of a door?

Thickness. Interior door thickness is an important consideration when it comes to installing doorknobs and hinges. The thinnest interior door you can buy is 1 3/8 inches thick, and the thickest is 1 3/4 inches thick, which is the same as an exterior door. Intermediary thicknesses include 1 1/2 and 1 5/8 inches.

How high is a standard door?

The height of common doors is 6 feet 8 inches. The standard height of the rough opening for a door is the door height plus 2 5/8 inches. The additional room allows for a 3/4-inch top jamb, a shim space above the door jamb and the thickness of underlayment and finish flooring.

How tall is a standard commercial door?

Commercial Door Height: The IBC states that doors should be at least 80 inches tall, with some exceptions.

How tall is the average front door?

Exterior doors often are the most visible parts of a house and like interior doors, are available in standard sizes. They range in width from 2 feet to more than 3 feet, and in height from 6 feet, 8 inches to more than 8 feet. Standard thickness is 1 3/4 inches.

What is the edge of the door called?

Butt. A door hinge, one leaf being mortised or routed into the door frame jamb and the other into the edge of the door. This is incorrectly called a “butt hinge” as the term “hinge” is usually applied to one which is attached to the surface of a door rather than to its edge such as a strap or T-hinge.

How big is the average doorway?

In the construction industry, this is often stated as 6/8, which means 6 feet 8 inches. Although this height is standard, actual door openings are sometimes slightly smaller or larger, such as 79 or 81 inches. Oversize exterior doors are sometimes 84 or 96 inches tall.

What is the standard door size?

Interior Doors. The height for all passage doors must be a minimum of 80 inches and the standard width sizes for interior doors are 24”, 28”, 30”, 32” and 36”. The minimum recommended door width to allow persons with disabilities’ to pass through is 36 inches.

What is the average size of a bathroom door?

Bathroom door size. A standard bathroom door is 32 inches (81cm). If you’re working with a really small space you could bring the door width down to 28 inches or 71cm, even down to 24 inches or 61cm as an absolute minimum (note – small doors are should only be used for bathrooms, closets and utility rooms).

How much room do you have to have around a toilet?

Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.

What is the minimum size for a bathroom?

A full bathroom usually requires a minimum of 36 to 40 square feet. A 5′ x 8′ is the most common dimensions of a guest bathroom or a master bathroom in a small house. If you happen to have this standard-sized small bathroom, there are two different layouts you can consider.

What is the minimum width required for a toilet?

Toilets. You need at least 30 inches (76 centimeters) of clear width for toilets, but 32 to 36 inches (81 to 91 centimeters) is much better for most people. Single sinks. For a single sink, you need at least 30 inches (76 centimeters) of width, but 36 to 48 inches (91 to 107 centimeters) is more comfortable.

How far does a toilet have to be away from a wall?

Standard drywall is 1/2 inch thick, so the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing.

What is the minimum distance from toilet to wall?

Recommended: Plan a clear floor space of at least 30 inches from the front edge of all fixtures (lavatory, toilet, bidet, tub, and shower) to any opposite bath fixture, wall, or obstacle. Code Requirement: A minimum space of 21 inches must be planned in front of lavatory, toilet, bidet, and tub.

What is a 10 inch rough in toilet?

Toilet rough in measuring: from wall to bolt cap. When talking toilets, the toilet rough in is the distance from the wall behind the toilet to the center of the outlet pipe where the waste leaves the toilet. The most common distance is 12 inches, so most toilets have a “12-inch rough.”

What is the rough in for a toilet?

To find out your toilet’s rough-in, measure from the wall behind the toilet to the middle of the closet bolts, which hold your toilet to the floor. That distance will likely be a bit more than the standard 10″, 12″, or 14″ rough-in dimensions. Round your measurement down to the nearest standard rough-in.

What size hole do you need for a toilet flange?

The ring has slots for the bolts that hold the toilet down. The flange pipe can have a diameter of either 3 or 4 inches, depending on the size of the waste line, but a 4-inch hole works in both cases. Plumbers cut it with a hole saw or a reciprocating saw.

What size hole to drill for a shower drain?

Drain Hole Size. The size of the drain hole depends on the size of your shower’s drain opening. Most shower drains utilize a 2-inch pipe. This means the hole you cut into the subfloor should be slightly larger than 2 inches in diameter.

What is proper toilet flange height?

First things to be careful of is proper flange height. With the toilet removed you can see the toilet flange and measure its height above the floor. Optimum flange height to aim for is 1/4 inch above the finished floor. This allows for basically any type of wax to be used and still get a great seal.

What is a full overlay on a hinge?

Full overlay hinges are for individual cabinets or the cabinets on either end of a run of cabinets. (Source) Half overlay hinges are intended for pairs of doors in the middle of a run of cabinets, where two doors have their hinges mounted on opposite sides of a shared middle partition.

Leave a Comment