What is the point of soffits?

Soffit serves both an aesthetic and functional purpose for a building’s roofing system. It’s the skin that covers your eaves — without it, you would see your rafter beams fully exposed. With vented soffit, air can flow through the vents to provide regular air circulation to your attic.

Herein, what is the difference between soffit and fascia?

The soffit board is tucked away under the fascia board. It is usually the board that you see most of from street level. The soffit can be ventilated to allow the flow of air into the roof area. Without adequate ventilation, condensation will form in the roof void increasing the risk of timber decay.

What is the trim around the roof called?

Roofing Terms. Eave: A roof edge that extends past the exterior wall line at the bottom of a slope. Fascia: Vertical roof trim located along the perimeter of a building, usually below the roof level, to cover the rafter tails at the eaves and to seal off the top of the siding along the rake; also called gutter boards.

How much does it cost for soffit and fascia?

Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.

What is the drip edge?

The lower edge of a roof should extend beyond the fascia board by about 3/4 inch so that runoff drains into the gutters. If this slight overhang is too short, water will drip behind the gutters, leading to rotted roof sheathing and fascia, stained siding, and even soil erosion and a flooded basement.

What is a fascia board made of?

Composite lumber is made from a mix of recycled wood chips, plastic and sawdust that is bound together with epoxy resin. While not as popular, this material can be used to make fascia boards.

What is a gable vents?

A Touch of Design. Unlike other passive venting systems, such as soffit or ridge vents, gable vents are meant to be seen. They are made visible on the front of a house or roof and add an architectural element to an otherwise invisible opening.

What is the gable of a house?

Gabled roofs are the kind young children typically draw. They have two sloping sides that come together at a ridge, creating end walls with a triangular extension, called a gable, at the top. The house shown here has two gable roofs and two dormers, each with gable roofs of their own.

What is the rake board?

A rake board. It’s not just what you use to clear your lawn of fallen leaves. On a gable roof, the rake board, or fascia, is the slanting edge at the end wall of the house. Contact H & S Roofing and Gutter to replace the rotten rake boards into beautiful new ones. Wood is the most commonly used material for a fascia.

What is flashing on the roof?

A: Tom Silva replies: Flashing is just material — usually aluminum or galvanized steel — that’s used over joints in roof and wall construction to prevent water seeping in and causing damage.

What is a ridge vent system?

A ridge vent is an important part of a home’s roofing system. Installed at the peak of a sloped roof, the ridge vent allows damp, warm air to escape from the attic. A properly installed ridge vent increases energy efficiency and prolongs the life of your roof.

What is the frieze board?

A frieze board is essentially a horizontal board between 2 inches and 6 inches wide, but this can vary for certain types of applications. A brick box is a type of house made mostly of brick.

What is the fascia of a car?

Fascia is a term used in two areas in the automotive world. Fascia often refers to the decorative panels of a car’s dashboard, or the dashboard assembly. Regulations affecting bumper design in the late 1970s saw the increasing use of soft plastic materials on the front and rear of vehicles.

What is the barge board?

Bargeboard (probably from Medieval Latin bargus, or barcus, a scaffold, and not from the now obsolete synonym “vergeboard”) is a board fastened to the projecting gables of a roof to give them strength, protection, and to conceal the otherwise exposed end of the horizontal timbers or purlins of the roof to which they

What is the difference between a soffit and fascia?

The soffit board is tucked away under the fascia board. It is usually the board that you see most of from street level. The soffit can be ventilated to allow the flow of air into the roof area. Alternatively, ventilation can be provided over the top of the fascia board.

What is a barge cap?

Stratco offers several different styles of Barge Capping to complete the edge of your roofing. Square Barges provide a neat finish and can be ordered in a variety of sizes to fit any style of roof sheeting. Roll barges have a curved edge that creates a traditional form that blends with corrugated sheeting.

What is a verge board?

Bargeboard is exterior house trim, usually ornately carved, that is attached along the roof line of a gable. Originally, this Victorian wood trim — also called vergeboard or verge board (verge being the end or edge of a thing) — was used to hide the ends of rafters. It hangs from the projecting end of a gable roof.

What is the verge of a roof?

Roof Verge Requiring Rebedding The edge of a pitched roof as it meets the gable end is called a verge. Tiles on the verge are often mortared to prevent rain and wind from getting underneath the tiles.

What is a dry verge on a roof?

‘Dry fixing’ is an increasingly popular roofing option which allows for the weather and pest-proofing of your roof without the need for mortar. Dry verge roofing makes use of interlocking caps that fit over the edge of your roof tiles, and offers an effective and, more importantly, durable alternative to wet verges.

What is pointing on a roof?

ROOF REPOINTING AND REBEDDING. Roof pointing is a second layer which goes over the top of the bedding to help create a stronger hold for on the tiles and seal the roof against dust and water. Cement mortar used to be used for roof pointing but has been replace by flexible pointing compounds.

Leave a Comment